ASK JOURNAL
ASKJ-2026-014 · Volume 1, Issue 1 — December 2026

Mooring-Line Entrapment and Load Redistribution During Berthing: A Case-Informed OPTIMOOR Assessment of Mona Manx

Haikal Asyraaf Abu Bakar Bakhri · Corresponding Author
Faculty of Maritime Studies, Universiti Malaysia Terengganu

Correspondence: haikalbakhri03@gmail.com

e-ISSN (online): 2838-0541 · Received: 2026-01-02 · Revised: 2026-05-13 · Accepted: 2026-10-26 · Published online: 2026-11-07
Download PDFDOI: 10.68949/askjv01i01a014Pages / article number: 173–185

Abstract

Mooring-line entrapment presents a hazard distinct from conventional rope parting: tensioned lines can recoil suddenly when released from berth structures, with a potentially large vertical trajectory. This study examines the fatal Mona Manx mooring accident at Puerto Ventanas, Chile, through documentary casualty analysis, a two-scenario OPTIMOOR mooring-load comparison, and exploratory expert ratings of operational risk factors. The Marine Accident Investigation Branch established that an aft spring line became entrapped near a berth fender and released as the vessel manoeuvred astern, fatally striking the second officer on 26 August 2021. The computational comparison reports two loaded lines at 73.8 under a case-informed arrangement, compared with 35.5 and 35.3 under a modified arrangement, reductions of 51.9% and 52.2%, respectively. The output force unit, strength-reference denominator, scenario settings, and compatibility of the reported steel-wire model with the casualty's high-strength copolymer rope were not established; the results therefore indicate within-model sensitivity rather than validated accident mechanics. Expert ratings rank organisational, individual and environmental considerations at 100, 87 and 60 on the study's reported scale, values that are not additive percentages of causation. A layered safety response prioritising master–pilot information exchange, prohibition of unauthorised engine-driven repositioning, fender-entrapment checks, three-dimensional recoil awareness, and disciplined communications follows from the combined technical and investigation findings. The analysis illustrates the value of case-informed scenario testing while demonstrating the need for transparent rope characterisation and model validation before quantitative safety limits are inferred.

mooring-line entrapmentOPTIMOORspring-line recoilmooring safetyhuman factors

Acknowledgement

The authors would like to express their sincere appreciation to all individuals and organisations who contributed to the successful completion of this study.

Conflict of interest

The authors declare that they have no known financial or non-financial competing interests that could have influenced the research presented in this manuscript.

References

Asmara, I. P. S., Dinata, S. M., Abdullah, K., Rochmad, A. N., & Sunardi. (2026). Risk-Informed Berthing Safety Envelope and Tug Power Requirements under Combined Environmental Disturbances Using Mathematical Maneuvering Group Maneuvering Simulation. International Journal of Safety and Security Engineering, 16(7). https://doi.org/10.18280/ijsse.160706

Bitting, K. R. (1982). A Snapback Evaluation Technique for Synthetic Lines. https://apps.dtic.mil/dtic/tr/fulltext/u2/a119070.pdf

Branch, M. A. I. (2024). Report on the investigation of a fatal accident during mooring operations on board the bulk carrier Mona Manx at Puerto Ventanas, Chile, on 26 August 2021. https://assets.publishing.service.gov.uk/media/673c705af2eda558e9494e7c/2024-18-MonaManx.pdf

Braun, V., & Clarke, V. (2006). Using thematic analysis in psychology. Qualitative Research in Psychology, 3(2), 77–101. https://doi.org/10.1191/1478088706qp063oa

Burton, R. A. (1987). WIRE ROPES AND SAFETY. Safety at Sea International, 222. https://trid.trb.org/view/397065

Cajiao, J., Argo, M. L., Bruin, W. M., Coughlan, P. J., Eskijian, M., Iverson, R. E., & Percher, M. (2025). Beginnings of a Unified Approach to Mooring Design: Equipment SWL Selection, Review, and Observations. 144–157. https://doi.org/10.1061/9780784486146.014

Carbonell, J. M., Monforte, L., Ciantia, M. O., Arroyo, M., & Gens, A. (2022). Geotechnical particle finite element method for modeling of soil-structure interaction under large deformation conditions. Journal of Rock Mechanics and Geotechnical Engineering, 14(3), 967–983. https://doi.org/10.1016/j.jrmge.2021.12.006

Ciceri, M., Aveline, C., Thillaithevan, D., Hewson, R., & Santer, M. (2026). A differentiable variational model for structural self-contact and fracture. Engineering With Computers, 42(2), 52. https://doi.org/10.1007/s00366-026-02285-6

Fan, S., & Yang, Z. (2023). Analysing seafarer competencies in a dynamic human-machine system. Ocean & Coastal Management, 240, 106662. https://doi.org/10.1016/j.ocecoaman.2023.106662

Forum, O. C. I. M. (2018). Mooring equipment guidelines. https://www.ocimf.org/publications/books/mooring-equipment-guidelines-meg4

Gao, F., Hu, K., Shen, W., & Li, Y. (2021). Study on the Safety Guarantee of Ship Mooring from Frequent Cable Accidents. IOP Conference Series Earth and Environmental Science, 621(1), 12007. https://doi.org/10.1088/1755-1315/621/1/012007

Gende, S. M., Vose, L., Baken, J., Gabriele, C. M., Preston, R., & Hendrix, A. N. (2019). Active Whale Avoidance by Large Ships: Components and Constraints of a Complementary Approach to Reducing Ship Strike Risk. Frontiers in Marine Science, 6. https://doi.org/10.3389/fmars.2019.00592

Gerasimov, T., & Lorenzis, L. D. (2019). On penalization in variational phase-field models of brittle fracture. arXiv (Cornell University), 354, 990–1026. https://doi.org/10.1016/j.cma.2019.05.038

Hao, S., Zhang, X., Yang, Y., Wang, B., & Bo, X. (2025). Mooring Failure Analysis of Semisubmersible Floating Offshore Wind Turbines Considering Mooring Redundancy at Each Azimuth Angle. Journal of Marine Science and Engineering, 13(2), 360. https://doi.org/10.3390/jmse13020360

Hao, X. Z. Q. (2024). Mooring Safety Analysis of Cable Breaking Accident of a Very Large Ore Carrier under Extreme Windy Weather Based on Numerical Simulation. Journal of Electrical Systems, 20(2), 1042–1051. https://doi.org/10.52783/jes.1283

Hasanspahić, N., Vujičić, S., & Mandušić, M. (2023). Ship Safety Officers’ Perceptions and Attitudes Toward Near-Miss Management Systems. Transactions on Maritime Science, 12(1). https://doi.org/10.7225/toms.v12.n01.w07

Hayes, S., & Fletcher, D. (2024). An overhead line virtual test track for the assessment of railway catenary pantograph interaction. Vehicle System Dynamics, 63(9), 1724–1744. https://doi.org/10.1080/00423114.2024.2382745

Hennø, E., & Schøyen, H. (2024). A lean approach to comparing the mooring systems of Suezmax tankers. Journal of Marine Science and Technology, 29(4), 956–974. https://doi.org/10.1007/s00773-024-01030-2

IMO. (2020a). Guidelines for inspection and maintenance of mooring equipment including lines (MSC.1/Circ.1620). https://www.imo.org/en/ourwork/safety/pages/safemooring.aspx

IMO. (2020b). Guidelines on the design of mooring arrangements and the selection of appropriate mooring equipment and fittings for safe mooring. https://wwwcdn.imo.org/localresources/en/Documents/MSC.1-Circ.1619%20-.pdf

Kamis, A. S., Fuad, A. F. A., Ashaari, A., & Yang, W. W. (2026). Directional sensitivity of wind current alignment in wheel over point geometry: development and validation of ATMM-W through percentage change. Journal of Marine Engineering & Technology, 25(5), 771–780. https://doi.org/10.1080/20464177.2026.2678623

Kery, S. (2018). Dynamic Modeling of Ship-to-Ship and Ship-to-Pier Mooring Performance. Marine Technology Society Journal, 52(5), 87–93. https://doi.org/10.4031/mtsj.52.5.10

Macrae, C. (2009). Human factors at sea: common patterns of error in groundings and collisions. Maritime Policy & Management, 36(1), 21–38. https://doi.org/10.1080/03088830802652262

MAIB. (2024). Report on the investigation of a fatal accident during mooring operations on board the bulk carrier Mona Manx at Puerto Ventanas, Chile, on 26 August 2021. https://assets.publishing.service.gov.uk/media/673c705af2eda558e9494e7c/2024-18-MonaManx.pdf

Matakis, K. E. (2010). Development of Wind and Current Coefficients for Multiple U.S. Navy Vessel Analysis Using OPTIMOOR. ASCE Ports Conference, 406–413. https://doi.org/10.1061/41098(368)42

Menteş, A., & Yetkin, M. (2022). AN APPLICATION OF SOFT COMPUTING TECHNIQUES TO PREDICT DYNAMIC BEHAVIOUR OF MOORING SYSTEMS. Brodogradnja, 73(2), 121–137. https://doi.org/10.21278/brod73207

Mooring System Engineering for Offshore Structures. (2019). In Elsevier eBooks. Elsevier BV. https://doi.org/10.1016/c2018-0-02217-3

Mujeeb-Ahmed, M. P., Cabrera-Miranda, J. M., Kim, H. J., & Paik, J. K. (2021). Effect of mooring line layout on the loads of ship-shaped offshore installations. Ocean Engineering, 241, 110071. https://doi.org/10.1016/j.oceaneng.2021.110071

OCIMF. (2018). Mooring equipment guidelines. https://www.ocimf.org/publications/books/mooring-equipment-guidelines-meg4

Pascoletti, G., Catelani, D., Conti, P., Cianetti, F., & Zanetti, E. M. (2019). Multibody Models for the Analysis of a Fall From Height: Accident, Suicide, or Murder? Frontiers in Bioengineering and Biotechnology, 7, 7–17. https://doi.org/10.3389/fbioe.2019.00419

Pastewka, L., Vakis, A. I., Eder, S. J., Aghababaei, R., Almqvist, A., Carbone, G., Chandross, M., Dini, D., Ehrich, H. J., Ewen, J. P., Menga, N., Molinari, J., Moras, G., Nicola, L., Paggi, M., Putignano, C., Scaraggi, M., Yastrebov, V. A., & Müser, M. H. (2025). Modeling in tribology: Recent advances, applications, and open questions. Tribology International, 218, 111326. https://doi.org/10.1016/j.triboint.2025.111326

Pillai, A. C., Gordelier, T., Thies, P. R., Dormenval, C., Wray, B., Parkinson, R., & Johanning, L. (2022). Anchor loads for shallow water mooring of a 15 MW floating wind turbine — Part I: Chain catenary moorings for single and shared anchor scenarios. Ocean Engineering, 266, 111816. https://doi.org/10.1016/j.oceaneng.2022.111816

Piskoty, G., Affolter, C., Sauder, M., Nambiar, M., & Weisse, B. (2017). Failure analysis of a ropeway accident focussing on the wire rope’s fracture load under lateral pressure. Engineering Failure Analysis, 82, 648–656. https://doi.org/10.1016/j.engfailanal.2017.05.003

Putra, G. R., Rosyid, D. M., & Prastianto, R. W. (2021). Mooring Lines Reliability Analysis Case Study: FSO Abherka. IPTEK The Journal for Technology and Science, 32(1), 41. https://doi.org/10.12962/j20882033.v32i1.3445

Roccia, B. A., Nguyen, T., Veseth, P., Nielsen, F. G., & Gebhardt, C. G. (2025). On the use of an advanced Kirchhoff rod model to study mooring lines. Marine Structures, 104, 103883. https://doi.org/10.1016/j.marstruc.2025.103883

Sholihin, Ramadhan, Y., & Armono, H. D. (2017). The Design of Mooring Dolphin Layout and Mooring Line Tension Analysis. International Journal of Offshore and Coastal Engineeing, 1(1), 22. https://doi.org/10.12962/j2580-0914.v1i1.2871

Singh, A., Dalaklis, D., & Baumler, R. (2023). Revisiting the HNoMS Helge Ingstad and Sola TS collision: Discussing the contribution of human factors. Maritime Technology and Research, 5(3), 262199. https://doi.org/10.33175/mtr.2023.262199

Surinov, I., Shemonayev, V., & Torskiy, V. G. (2025). Simultaneous Operations During LNG Bunkering at LNG-powered Vessels. TransNav the International Journal on Marine Navigation and Safety of Sea Transportation, 19(4), 1361–1370. https://doi.org/10.12716/1001.19.04.36

Swenson, R. C. (1983, May 2). A Snap-Back Restrained Kevlar Mooring Line. Offshore Technology Conference. https://doi.org/10.4043/4636-ms

Thorenz, C., & Schulze, L. (2021). Numerical investigations of ship forces during lockage. Journal of Coastal and Hydraulic Structures. https://doi.org/10.48438/jchs.2021.0005

Torres-Zúñiga, V. (2024). Recreación por computadora de una precipitación con enganches entre barandales. Revista Logos Ciencia & Tecnología, 16(3), 88–104. https://doi.org/10.22335/rlct.v16i3.1968

Trubat, P., Molins, C., & Gironella, X. (2019). Wave hydrodynamic forces over mooring lines on floating offshore wind turbines. Ocean Engineering, 195, 106730. https://doi.org/10.1016/j.oceaneng.2019.106730

Vidmar, P., Perkovič, M., Gucma, L., & Łazuga, K. (2020). Risk Assessment of Moored and Passing Ships. Applied Sciences, 10(19), 6825. https://doi.org/10.3390/app10196825

Villa, R., Carral, J. C., Solutions, C. D. E., Fraguela, J. Á., López, M., & Carral, L. (2017). A REVIEW OF SHIP MOORING SYSTEMS. Brodogradnja, 69(1), 123–149. https://doi.org/10.21278/brod69108

Yang, K.-M., Feng, A., Xu, S., & Yuan, Z. (2026). Design and hydrodynamic analysis of a new web-type mooring system. Ocean Engineering, 368, 128312. https://doi.org/10.1016/j.oceaneng.2026.128312

Zhao, C., Zhang, W., Chen, C., Yang, X., Yue, J., & Han, B. (2023). Recognition of Unsafe Onboard Mooring and Unmooring Operation Behavior Based on Improved YOLO-v4 Algorithm. Journal of Marine Science and Engineering, 11(2), 291. https://doi.org/10.3390/jmse11020291

Zwijnsvoorde, T. V., Vantorre, M., Eloot, K., & Ides, S. (2019). Safety of container ship (un)loading operations in the Port of Antwerp. Maritime Business Review, 4(1), 106–127. https://doi.org/10.1108/mabr-09-2018-0033

Creative Commons Attribution 4.0 International badge

© 2026 The Author(s). This article is licensed under a Creative Commons Attribution 4.0 International License (CC BY 4.0).