ASK JOURNAL
ASKJ-2026-010 · Volume 1, Issue 1 — December 2026

Comparative Assessment of Maintenance Requirements and Perceived Economic Feasibility of HDPE, Fibreglass and Inflatable Boats

Khairina Ayu Alisha Shakor · Corresponding Author
Faculty of Maritime Studies, Universiti Malaysia Terengganu

Ahmad Faizal Ahmad Fuad
Faculty of Maritime Studies, Universiti Malaysia Terengganu

Correspondence: s65743@ocean.umt.edu.my

e-ISSN (online): 2838-0541 · Received: 2025-12-29 · Revised: 2026-02-26 · Accepted: 2026-10-21 · Published online: 2026-11-07
Download PDFDOI: 10.68949/askjv01i01a010Pages / article number: 127–139

Abstract

High-density polyethylene (HDPE), fibreglass-reinforced polymer and inflatable construction each offer different procurement, operating and maintenance characteristics for small boats. This descriptive comparative study examined the perceived maintenance practicality and economic considerations of these three hull types using a four-point questionnaire administered to 12 maritime practitioners, alongside a review of marine materials and boatbuilding literature. Respondents included maintenance personnel (50.0%), manufacturers (33.3%), a marine drafter (8.3%) and another maritime practitioner (8.3%). The reported item-level ratings were organised into repair complexity, cleaning requirements and service intervals. Unadjusted averages for HDPE, inflatable and fibreglass boats, respectively, were 3.80, 2.50 and 3.00 for repair items; 3.90, 2.90 and 2.60 for cleaning; and 3.50, 2.90 and 3.00 for servicing. These descriptive averages reproduce the available item summaries but contain positively and negatively phrased statements. Because individual response records and documented polarity rules were unavailable, the averages cannot be accepted as validated comparative maintenance-performance scores. An explicit polarity-adjusted sensitivity calculation reveals that the interpretation of repair complexity may change when negative items are reversed. The evidence suggests potential practical advantages of HDPE for particular small-craft applications but does not establish monetary lifecycle savings or universal technical superiority. The study identifies priorities for consistent repair training, material-specific maintenance protocols, comparable cost records and more robust vessel-level evaluation.

high-density polyethylenesmall-boat constructionfibreglassinflatable boatslifecycle cost

Acknowledgement

The authors acknowledge the guidance provided by Universiti Malaysia Terengganu and the participation of respondents associated with MSET Holdings Sdn. Bhd. and Sulong Shipyard Sdn. Bhd. Their contributions supported the completion of the study. The authors also acknowledge the encouragement of family and colleagues.

Conflict of interest

The authors declare that they have no known financial or non-financial conflicts of interest that could have influenced the research, analysis, interpretation, or publication of this manuscript.

References

Alhatti, A. I., Deveci, S., Barsoum, I., & Hosny, A. I. (2025). Advancements in butt fusion jointing of HDPE pipes: A comprehensive review of fusion conditions and joint integrity assessment techniques. Polymer Testing, 150, 108909. https://doi.org/10.1016/j.polymertesting.2025.108909

Amiruddin, W., Hadi, E. S., & Kiryanto, K. (2014). PEMANFAATAN MATERIAL PLASTIK HDPE BEKAS DRUM KEMASAN SEBAGAI KULIT LAMBUNG PERAHU. SHILAP Revista de Lepidopterología. https://doi.org/10.12777/kpl.11.3.162-169

Bertagna, S., Marchesi, N. T., Bucci, V., Brando, G., Distefano, F., Crupi, V., & Marinò, A. (2025). Investigation on the Tensile Properties of Virgin and Recycled HDPE for Boatbuilding Applications Through Experimental Tests. In Progress in marine science and technology. IOS Press. https://doi.org/10.3233/pmst250118

Bertagna, S., Marchesi, N. T., Bucci, V., & Marinò, A. (2024). On the Structural Response of Innovative Plastic Materials for Boatbuilding Applications. In Progress in marine science and technology. IOS Press. https://doi.org/10.3233/pmst240024

Bosseler, B., Homann, D., Brüggemann, T., Naismith, I., & Rubinato, M. (2023). Quality assessment of CIPP lining in sewers: Crucial knowledge acquired by IKT and research gaps identified in Germany. Pure (Coventry University), 143, 105425. https://doi.org/10.1016/j.tust.2023.105425

Brawijaya, U., Kadhafi, M., Sunardi, S., Triono, A., Jember, U., Sari, W. K., & Brawijaya, U. (2021). Studi Karakteristik Stabilitas dan Konstruksi Kapal Berbahan High Density Polyethylene (HDPE). Jurnal Rekayasa Mesin, 12(2), 315–323. https://doi.org/10.21776/ub.jrm.2021.012.02.9

Chen, X., Su, Y., Reay, D., & Riffat, S. (2016). Recent research developments in polymer heat exchangers – A review. Renewable and Sustainable Energy Reviews, 60, 1367–1386. https://doi.org/10.1016/j.rser.2016.03.024

Dorland, J., & Jørgensen, M. S. (2025). Unpacking Repair: A Comparative Study of Socio-Technical Factors Influencing Consumer Decisions in the Circular Economy across Three Product Categories. Circular Economy and Sustainability, 5(5), 3991–4026. https://doi.org/10.1007/s43615-025-00596-2

Ehlen, M. A. (1997). Life-Cycle Costs of New Construction Materials. Journal of Infrastructure Systems, 3(4), 129–133. https://doi.org/10.1061/(asce)1076-0342(1997)3:4(129)

Firmanda, T., Anggara, S., Hariadi, M. R. F., & Prakasa, A. R. (2022). HDPE as a New Alternative Material for Small Vessel Boat Strength. International Conference on Applied Science and Technology on Engineering Science (iCAST-ES), 473–477. https://doi.org/10.5220/0011814700003575

Frej, H. B. H., Léger, R., Perrin, D., & Ienny, P. (2021). A Novel Thermoplastic Composite for Marine Applications: Comparison of the Effects of Aging on Mechanical Properties and Diffusion Mechanisms. Applied Composite Materials, 28(4), 899–922. https://doi.org/10.1007/s10443-021-09903-0

Gölpınar, S. (2005). Comparative analysis of materials in recreational boat design: fiber reinforced plastic boat in serial production [Izmir Institute of Technology]. In İYTE (İZMİR YÜKSEK TEKNOLOJİ ENSTİTÜSÜ). http://hdl.handle.net/11147/3276

Hrabenko, A. A., & Kuznetsov, A. I. (2021). APPLICATION FEATURES OF LOW-PRESSURE POLYETHYLENE AS A MATERIAL OF HULL STRUCTURES OF SMALL VESSELS. Collection of Scientific Publications NUS, 2, 3–7. https://doi.org/10.15589/znp2021.2(485).1

Ilg, P., Hoehne, C., & Guenther, E. (2015). High-performance materials in infrastructure: a review of applied life cycle costing and its drivers – the case of fiber-reinforced composites. Journal of Cleaner Production, 112, 926–945. https://doi.org/10.1016/j.jclepro.2015.07.051

Lee, S.-R., Kang, G.-J., & Cho, S.-S. (2017). Evaluation of Structural Safety of Polyethylene Boats by Drop Test Method. Journal of the Korea Academia-Industrial Cooperation Society, 18(5), 531–542. https://doi.org/10.5762/kais.2017.18.5.531

Mahl, M., Jelich, C., & Baier, H. (2019). On the Temperature-Dependent Non-Isosensitive Mechanical Behavior of Polyethylene in a Hydrogen Pressure Vessel. Procedia Manufacturing, 30, 475–482. https://doi.org/10.1016/j.promfg.2019.02.067

Nisazarifa, A., Nursyifaulkhair, D., Rosalina, A., Wibawa, I. P. A., & Saputra, M. R. A. (2026). Sustainable Boatbuilding: Evaluating the Feasibility of Recycled HDPE as a Structural Material. Springer Link (Chiba Institute of Technology). https://doi.org/10.1051/bioconf/202621605001/pdf

Norgren, A., Carpenter, A., & Heath, G. (2020). Design for Recycling Principles Applicable to Selected Clean Energy Technologies: Crystalline-Silicon Photovoltaic Modules, Electric Vehicle Batteries, and Wind Turbine Blades. Journal of Sustainable Metallurgy, 6(4), 761–774. https://doi.org/10.1007/s40831-020-00313-3

Pommier, R., Grimaud, G., Prinçaud, M., Perry, N., & Sonnemann, G. (2015). Comparative environmental life cycle assessment of materials in wooden boat ecodesign. The International Journal of Life Cycle Assessment, 21(2), 265–275. https://doi.org/10.1007/s11367-015-1009-1

Purwoko, M. S., Jamal, J., Santoso, B., Siswandi, S., & Romadhoni, R. (2024). ANALISI STABILITAS KAPAL RISET POLBENG DI PERAIRAN SEA-STATE 3. INOVTEK POLBENG, 14(2), 152–161. https://doi.org/10.35314/42vwet48

Ridwan, M., Sulaiman, S. M., Sugeng, S., Sarwoko, S., & Nies, H. (2022). Mechanical Properties of Small Boat Construction from HDPE Blue Drum Scrap. TransNav the International Journal on Marine Navigation and Safety of Sea Transportation, 16(3), 573–578. https://doi.org/10.12716/1001.16.03.20

Said, M. S. (1999). Mechanical Behavior of Fabric-Film Laminates. NASA STI Repository (National Aeronautics and Space Administration). http://hdl.handle.net/2060/19990064447

Sözen, A., & Neşer, G. (2024). On the printability of high-density polyethylene (HDPE) reinforced with long glass and short carbon fibres. Rapid Prototyping Journal, 31(2), 432–446. https://doi.org/10.1108/rpj-01-2024-0032

Supomo, H., Baihaqi, I., Safaruddin, A. R., & Supomo, W. S. (2024). Techno-economic Study of Recycled Plastic Waste Boards (RPB) as Sustainable Shell Construction Material for Fishing Vessels in Indonesia. Kapal Jurnal Ilmu Pengetahuan Dan Teknologi Kelautan, 22(2), 94–108. https://doi.org/10.14710/kapal.v22i2.68193

Telak, O., Telak, J., & Niemczewski, T. (2023). Motor Boats in the Technology of HDPE with RIB Type Construction. Bezpieczeństwo i Technika Pożarnicza, 61(1), 166–178. https://doi.org/10.12845/sft.61.1.2023.10

Veritas, B. (2022). Hull in composite, plywood and high density polyethylene materials (NR546, Rev. 04). https://marine-offshore.bureauveritas.com/nr546-hull-composite-plywood-and-high-density-polyethylene-materials

Vizentin, G., & Vukelić, G. (2020). Degradation and Damage of Composite Materials in Marine Environment. Materials Science, 26(3), 337–342. https://doi.org/10.5755/j01.ms.26.3.22950

Watt, E., Picard, M., Maldonado, B., Abdelwahab, M. A., Mielewski, D. F., Drzal, L. T., Misra, M., & Mohanty, A. K. (2021). Ocean plastics: environmental implications and potential routes for mitigation – a perspective. RSC Advances, 11(35), 21447–21462. https://doi.org/10.1039/d1ra00353d

Wibawa, I. P. A., & Birmingham, R. (2018). Fiberglass reinforced plastic as construction material for Indonesian fishing vessels – challenges and future potential development. MATEC Web of Conferences, 204, 5009. https://doi.org/10.1051/matecconf/201820405009

Wibawa, P. A., Razzaqi, A., Abdullah, K., Wulandari, K., Sumardiono, S., Restu, E., & Gafur, M. A. (2023). Analysis of tensile and flexural strength of HDPE material joints in ship construction. Istrazivanja i Projektovanja Za Privredu, 21(2), 668–677. https://doi.org/10.5937/jaes0-41924

Creative Commons Attribution 4.0 International badge

© 2026 The Author(s). This article is licensed under a Creative Commons Attribution 4.0 International License (CC BY 4.0).